Oil & Petrolium Instruments

MELTING POINT APPARATUS

This apparatus consists of a cylindrical block of Aluminium with a built in electrical heating element. The mounted Alum. block illuminates from below by a lamp fixed in its housing. The aluminium block accept three capillary tubes and mercury thermometer. The temperature is controlled by rotary switch. The magnifying lense provided for viewing objects clear. Suitable for operation on 220 Volts AC circuits.

Various Viscometers may be fixed as an internal part of bath . The bath is rectangular in shape. Inside tank made of Stainless steel sheet. On two sides toughened glass provided for full visibility of objects.

The bath is controlled by an electronic relay and Digital Controller Temperature range 5°C above room temperature to 95°C. Accuracy 0.1°C Stirring is done by a F.H.P. elect. motor stirrer. It is Supplied with Viscometer tube holders and S.S. cover.

PENSKY MARTEN FLASH POINT APPARATUS

This apparatus is made as per IP 34, ASTMD-93 and 151448 (Part I) 1270 (P.21) and IS 1209-1953 method B. Used for finding out Flash Point above 70°C and below 300°C. The Instrument having Oil Test Jet/Gas Test Jet Flame Device, stirrer with flexible shaft. The Assembly rests in Air Bath which is covered with Dome shape metal top. The cup is fitted with insulated Handle and locking arrangement near Cup flange. The assemble is kept on round shape electric heater with Seperate temp. regulator. Suitable for operation on 220 Volts 50 cycles AC Circuits.

Gas Flowmeter

It is of rotary and wet type with a capacity of 1 liter revolution. This is fabricated out of stainless steel and supported on adjustable tripod Stand. The meter is for use under pressure condition not exceeding 8 inches water column. When the pressure exceeds this limit suitable pressure governors are to be made use for regulating the pressure.

The dial is graduated with a smallest division of 0.02 liter and has an accuracy of 0.5% of full scale. The meter is supplied with a sprit level and a thermometer 0 50 C sheathed in Metal Pipe.

Aniline Point Apparatus, Model MIC 168

Aniline point apparatus as per IP 2 & IS 1448 (P-3), ASTM D 611 method A complete with jaket Electric heated with energy regular control (without thermometer)    

REDWOOD VISCOMETERS

These viscometers are designed for viscosity tests of petroleum Products. They confirm torequirements of IP 70 (Former). Two adaption of Red Wood viscometer are available No. 1 for liquids having Red Wood flow 20 seconds to 2000 seconds and No. II for liquids whose flow time exceeds 2000 seconds. The complete outfit comprises Stainless steel bath with electrical heating arrangement suitable to operate at 220 Volts AC Mains with tap, oil cup with precision stainless steel jet, cup cover, ball valve, and thermometer-clip. Stirrer and M.S. Sheet stand

REID VAPOUR PRESSURE TEST APPARATUS

The Vapour pressure bomb is made of brass heavily Chromium plated and consists of air chamber and gasoline chamber. A pressure gauge of required range isfitted abovethe air chamber The joints are made leak proof by neoprene washers. The water bath used is of such dimensions that the vapour pressure bomb immersed to at least 1 inch above the air chamber and maintained at a constant temperature upto 80°C ± 1°C. with FHP Stirrer and with PID Digital Temp. Controller.

SAYBOLT VISCOMETER APPARATUS

Made as per ASTMD-88 specifications with two jets one Universal and Furol Jets made of Stainless Steel. Stirring is done by hand with turn table arrangement (without strainer, withdrawl tube and glasswares) suitable to operate on 200 volts AC Mains. 

SMOKE POINT APPARATUS

Smoke Point Apparatus as per IP 57 & IS 1448 (P-31) &ASTM D 1322

SOFTENING POINT APPARATUS

For determination of softening point of bituminious materials according to IP 58 and IS 1205-1958. Softening point is that temperature at which the speciman under test becomes soft enough to allow a steel ball of specific dimensions to fall a required distance under test condition. The apparatus consists of glass beaker, ring Stand, two steel balls with rings and ball guides, hand Stirrer.

TAR VISCOMETER APPARATUS

As per IP 72 and IS 1206 standards. It is used for determination the viscosity of road oils and cut back bitumen. It consists S.S. Bath with cup of 10 mm or 4mm orifice and sleeve, Stirrer with lifting clip and ball. The assembly kept on Suitable stand with leveling screws. Suitable to operate on 220 volts AC Mains.

SEMI AUTOMATIC BOMB CALORIMETER APPARATUS

All calculations are done Automatically by system itself and then are automatically displayed, printed and transferred to PC Micro controller based.

·       Automatic Measurement and calculation of calorific values/water Equivalent.

·       Timer control through RTC which makes it highly accurate.

·       Thermal Printer interface for printing the final Result.

·       Soft touch keypad for menu driven setting of different Parameters.

·       Automatic measurement and mathematical calculation of the calorific value /water Equivalent which eliminate the presence of operator to be continuous to note the maximum temp. rise.

·       Weight of tablet/ water equivalent feedablethough keypad by user.

·       Full test report print out with date and time and company name.

·       True to scanning resolution of 0° 01°C

·       PC Software for data record

BOMB CALORIMETER APPARATUS

It is used for determination of calorific value of liquid & Solid fuels. The Instrument consists S.S. Body made out of corrosion resisting stainless steel Rod cap. 300 ml, Calorimeter vessel, outer Jacket with insulated Body, offset stirrer, S.S. Crucible, pellet press, ignition wire, and pressure gauge, with flexible pipes, with electronic firing unit.

Pressure Governor

This is to regulate the Pressure of gas before it enters the flow meter. This is also fabricated out of stainless steel and is supplied with a beam balance of knife edge, counter balance shot tube, inlet and outlet nozzles. Since the burner nozzle is designed for 2 inches W.G. pressure the governor reduces the main pressure to 2 inches and the main pressure should not exceed 10 inches W.G. Bedsides the above three major components with their accessories, the equipment consists of Digital Display Unit with two sensors measuring inlet and outlet temperature of water and one number of 0-50 X 1 C for effluent gas and measuring jar of 2 Ltr. capacity and 50 ml capacity and rubber tubing for connection.

REDWOOD VISCOMETER MULTIPLE APPARATUS, Model MIC-109

It consists, One Red Wood No.1 cup and One Red Wood No. 2 cup are installed in the bath. The bath is made from S.S. Sheet The temperature is Controlled by Electronic Digital Temperature Controller. The Stirring is done by FHP electric motor in the heating compartment. The unit has 2 sets of Oil Cup covers, thermometer Clips and ball valve. Suitable to operate on 220 volts AC Circuits.

TAR VISCOMETER MULTIPLE APPARATUS

Consist 2 cups in a S.S. Water Bath mounted on Stand with levelling feet. Fitted with 1000 watts heater. Temperature is controlled by DIGITAL ELECTRONIC CONTROLLER with F.H.P. electric motor Stirrer. Supplied with one Tar Cup 10mm and one4 mm orifice with Valves